;--------------------------------------------------------------------------
;
;
;   PEEDI target configuration file
;
;   Supported devices   : Freescale iMX25, ARM926ejs
;   Board               : Logitech Baby Boom
;
;
;--------------------------------------------------------------------------

;--------------------------------------------------------------------------
; The following section contains licenses that are required for PEEDI to
; operate.
;
; These licenses must be filled before using this file.
;
;   Example:
;       [LICENSE]
;       KEY         = UPDATE_24MAY2007, 1111-1111-1111-1
;       KEY         = ARM7, 2222-2222-2222-2
;
; The minimum required licenses are provided when PEEDI is purchased and 
; are printed on the bottom side of PEEDI.
;

[LICENSE]
; UK Office PEEDI SN: PD-0000-113A-D98D
KEY=UPDATE_15DEC2009, 1OH5-GOIQ-8P6E-O
KEY=ARM7_ARM9, JO4I-SUCM-5HUU-Q
KEY=GDB_REMOTE, B766-Q3OM-V7ME-T
KEY=ARM11, 020D-TIF7-9S9K-5

; MV Office PEEDI SN: PD-0000-113A-D6B2
KEY=UPDATE_13DEC2009, 9SFI-81OM-K0I2-7
KEY=ARM7_ARM9, 6UOE-MKN9-5H41-4
KEY=GDB_REMOTE, QHBE-5F1E-JFP4-R
KEY=ARM11, PGQV-HAEI-HG67-0

;--------------------------------------------------------------------------

[DEBUGGER]
PROTOCOL                = gdb_remote    ; gdb remote
REMOTE_PORT             = 2000          ; TCP/IP port
GDB_READ_INGNORE_TIME   = 3000

[TARGET]
PLATFORM                = ARM           ; platform is ARM9

[PLATFORM_ARM]
JTAG_CHAIN              = 5,4,4,4       ; list of IR lenght of all TAP controllers in JTAG chain
JTAG_CLOCK              = 10, 10000     ; JTAG Clock in [kHz] - 10kHz jtag clock for init operations and 10MHz for normal work
JTAG_TDO_DELAY          = AUTO
TRST_TYPE               = OPENDRAIN     ; type of TRST output: OPENDRAIN or PUSHPULL
RESET_TIME              = 200           ; lenght of RESET pulse in ms; 0 means no RESET

CORE0                   = ARM926E, 2, 0x7926041    ; TAP is ARM926ejs  CPU
CORE0_BREAKMODE         = soft          ; breakpoint mode
;CORE0_INIT              = INIT_FAB4_DDR     ; init section for the CPU
CORE0_FLASH0            = FLASH_NAND_BOOT   ; flash section parameters
CORE0_ENDIAN            = LITTLE        ; core is little endian
; workspace in internal SRAM
CORE0_WORKSPACE_ADDR    = 0x78000000    ; start address of workspace for flash programmer
CORE0_WORKSPACE_LEN     = 0x10000       ; length of workspace in bytes
CORE0_STARTUP_MODE      = RUN ; or RESET
;CORE0_VECTOR_CATCH_MASK = 0xFF
CORE0_PATH              = "http://172.19.113.252"      ; default path 
CORE0_DCC_PORT          = 3000

[FLASH_NAND_BOOT]
CHIP                = NAND_FLASH
CPU                 = iMX25
ADDR_BASE           = 0
FILE                = "/redboot.bin", 0x0000000
;BAD_BLOCKS         = 2819, 3067, 3071, 3585
ERASE_BAD_BLOCKS    = NO
OOB_INFO            = IMX_ECC


[SERIAL]                                ; serial port configuration
BAUD                = 115200
STOP_BITS           = 1
PARITY              = NONE
;TCP_PORT            = 2001


[TELNET]
PROMPT              = "baby> "          ; telnet prompt
;BACKSPACE          = 127               ; comment out for autodetect


[DISPLAY]
BRIGHTNESS          = 20                ; LED indicator brightness
VOLUME              = 25                ; zummer volume